NbTi Superconducting Coaxial Cables | 034, 047, 086 Cryogenic RF Cable | Vinstronics
Home / RF Coaxial Cable / NbTi Superconducting Coaxial Cables
4 K-to-mK Routing NbTi Conductors 034 / 047 / 086 Formats

NbTi Superconducting Coaxial Cables for Cryogenic RF Routing

Vinstronics provides NbTi superconducting coaxial cable assemblies for 4 K-to-mK microwave paths in dilution refrigerators, quantum computing systems, and low-temperature instrumentation. Select 034, 047, or 086 formats with connector interface, bend envelope, magnetic requirement, and cryogenic stage reviewed before build.

The 034, 047, and 086 labels refer to common nominal coaxial size families, broadly associated with 0.86 mm, 1.22 mm, and 2.13 mm OD formats.

Cryogenic Signal Path Logic
300 K to 4 KThermal isolation / attenuation strategy
4 K to mKNbTi superconducting microwave path
Electricalfrequency, return-loss requirement, connector transition
Mechanicallength, routing envelope, bend condition, thermal anchor
Cryogenictarget stage, heat-load sensitivity, test reference needs
Magneticnon-magnetic connector and material review

Use this page as a format-selection reference. Final operating frequency, return loss, bend limit, and connector compatibility depend on the finished assembly configuration and should be confirmed against datasheet or drawing.

Compare Formats →
Definition

What Is an NbTi Superconducting Coaxial Cable?

NbTi superconducting coaxial cable uses niobium-titanium conductors in a coaxial transmission-line structure. It is typically selected for low-temperature microwave paths where conductor loss, thermal conduction, routing density, and magnetic compatibility must be considered together.

For dilution refrigerator and quantum-system wiring, the cable format should be selected with the cryogenic stage, cable length, connector interface, bend envelope, routing density, and system drawing in view. Performance claims should be reviewed against the finished assembly and test condition.

Product Formats

Select 034, 047, or 086 NbTi Coax

Each nominal format supports a different balance of routing density, handling margin, connector transition, and mechanical envelope. Product pages provide the model-level entry point; final assembly review should be based on connector choice, length, bend condition, and cryogenic stage.

034 NbTi superconducting coaxial cable format

034 NbTi Coax — Dense mK-Stage Routing

Small-format NbTi coax for dense microwave routing near the lowest cryogenic stages where space is limited and handling margin must be reviewed carefully.

Model: G08E-NT
OD Reference: 0.86 mm
Selection Focus: routing density
047 NbTi superconducting coaxial cable format

047 NbTi Coax — Balanced Cryogenic Routing

Mid-format NbTi coax for cryogenic microwave lines requiring a balance of routing density, mechanical handling, and connector termination review.

Model: G12E-NT
OD Reference: 1.22 mm
Selection Focus: balanced routing
086 NbTi superconducting coaxial cable format

086 NbTi Coax — Robust Low-Density Routing

Larger-format NbTi coax for routes where handling margin, connector strategy, or assembly robustness is more important than maximum line density.

Model: G22-NT
OD Reference: 2.13 mm
Selection Focus: handling margin
Selection Matrix

Core Selection Matrix

Use the matrix to compare nominal format, physical size, and selection focus. Cutoff frequency is a geometry-based reference, not a guaranteed operating frequency.

Model Nominal Format OD Reference Nominal Impedance Cutoff Reference Bend-Radius Note Recommended Selection Focus Connector Review Product Page
G08E-NT 034 0.86 mm 50 Ω nominal 154 GHz reference Confirm condition in datasheet and assembly drawing Dense routing where available envelope is limited Review connector transition, magnetic requirement, and handling margin View Details
G12E-NT 047 1.22 mm 50 Ω nominal 110 GHz reference Confirm condition in datasheet and assembly drawing Balanced density, handling, and termination review Review connector transition, magnetic requirement, and bend envelope View Details
G22-NT 086 2.13 mm 50 Ω nominal 68 GHz reference Confirm condition in datasheet and assembly drawing Lower-density route with more handling margin Review connector interface, length, routing envelope, and support bracket View Details
Frequency noteCutoff reference is not a guaranteed operating frequency. Final operating frequency depends on connector transition, assembly length, bend condition, and return-loss requirement.
Bend noteBend-radius values must be confirmed against datasheet, installation condition, and finished assembly drawing.
Build noteNon-magnetic connector termination, finished length, routing envelope, and cryogenic stage should be reviewed before quotation.
Cable Type Boundary

Superconducting vs Standard Cryogenic Coaxial Cable

Cryogenic RF cable selection is not only a material choice. Thermal stage, routing flexibility, magnetic requirement, connector termination, and RF performance targets should be reviewed together.

Stainless Steel / CuNi Cryogenic Coax

Often selected where thermal isolation across higher-temperature stages is a key requirement. Final RF loss and heat-load behavior depend on cable design and assembly condition.

Flexible Low-Temperature Coax

Flexible low-temperature coaxial cables may use different conductor and dielectric systems depending on routing flexibility, thermal isolation, and stage location. Material selection should be reviewed against cable design and system requirements.

NbTi Superconducting Coax

Typically selected for 4 K-to-mK microwave paths where low conductor loss, low heat conduction, and magnetic compatibility may all affect signal-path selection.

Inquiry Checklist

Information Needed for Engineering Review

Providing these details helps Vinstronics review the cable format, connector transition, length, magnetic requirement, and assembly feasibility before quotation.

Cryogenic stage4 K, still, cold plate, mixing chamber, or other routing location.
Cable lengthFinished length, tolerance, and routing path if available.
Connector interfaceSMA, SMP, 2.92 mm, or other interface requirement for review.
Routing envelopeAvailable space, bracket location, thermal-anchor points, and bend constraints.
Magnetic requirementNon-magnetic connector/material requirement and system sensitivity.
Data requestDatasheet, dimensional drawing, and available test reference upon request.
Engineering FAQ

Common Questions Before Selecting NbTi Coax

What is an NbTi superconducting coaxial cable?
It is a coaxial transmission line using niobium-titanium conductors, typically selected for low-temperature microwave routing where conductor loss, heat conduction, and magnetic compatibility must be evaluated together.
How is NbTi coax different from standard cryogenic coax?
Standard cryogenic coax may prioritize thermal isolation or flexible low-temperature routing. NbTi superconducting coax is typically selected for 4 K-to-mK paths where low conductor loss and low thermal conduction are both relevant.
Is cutoff frequency the same as recommended operating frequency?
No. Cutoff frequency is a geometry-based reference. Recommended operating frequency depends on connector transition, assembly length, bend condition, return-loss requirement, and test environment.
How should I choose between 034, 047, and 086?
Select by routing density, handling margin, connector interface, bend envelope, and cryogenic-stage location. Final choice should be reviewed against the system drawing.
Are non-magnetic connectors required?
Non-magnetic connector options are recommended for magnetically sensitive cryogenic or quantum systems, but the requirement should be confirmed against the system magnetic and mechanical constraints.
What information is required for a quote or engineering recommendation?
Provide the target cryogenic stage, cable length, connector interface, routing envelope, bend constraints, magnetic requirement, target frequency range, and requested datasheet or test references.
Can Vinstronics support custom connector termination?
Vinstronics can review custom connector termination requirements for NbTi cable assemblies. Feasibility depends on cable format, connector interface, magnetic requirement, length, and assembly drawing.

Request Technical Datasheet

Request current dimensional drawings, material stack, connector options, bend-radius notes, and available test references for 034, 047, and 086 NbTi cable assemblies.

Request Engineering Review

Send the target cryogenic stage, cable length, connector interface, routing envelope, bend limit, and magnetic requirement. Vinstronics will review the suitable NbTi format and connector strategy for the finished assembly.

Request a Quick Quote