1.0 mm Male-to-Male Integrated Armored RF Test Cable Assembly, DC–110 GHz | VST-L-10M10M-T18KB-XXXX
P/N: VST-L-10M10M-T18KB-XXXX
• DC–110 GHz performance with precision 1.0 mm male interfaces
• VSWR ≤1.45 across the full rated frequency range
• Integrated armored construction for repeated high-frequency test routing
• Configurable lengths with insertion loss documented in the corresponding test report
• Minimum bend radius 30 mm; operating temperature -55°C to +125°C
VST-L-10M10M-T18KB-XXXX is a 50 Ω 1.0 mm male-to-male integrated armored RF test cable assembly for precision microwave and millimeter-wave measurements from DC to 110 GHz. It combines 1.0 mm precision interfaces with a protected cable construction for broadband test interconnects through 110 GHz.
The assembly is specified for VSWR ≤1.45 across DC–110 GHz and ±1 ps phase matching for paired assemblies, with an operating temperature range of -55°C to +125°C and shielding effectiveness of ≥90 dB at 1 GHz. Assembly length is configurable; insertion loss is documented in the corresponding test report.
DC–110 GHz Performance
Precision 1.0 mm male interfaces support broadband microwave and W-band test interconnects through 110 GHz.
VSWR ≤1.45 to 110 GHz
VSWR is specified at ≤1.45 across the full DC–110 GHz rated frequency range.
Integrated Armored Construction
Protective outer construction and reinforced connector transitions support repeated high-frequency test routing and handling.
±1 ps Phase Matching for Pairs
Paired assemblies can be phase matched to ±1 ps for measurement setups that require closely matched electrical paths.
For measurements through 110 GHz, assembly length, routing, connector condition, and mating practice should be considered together with the required insertion-loss and phase-matching requirements. The 1.0 mm male-to-male configuration is intended for precision coaxial interconnection between high-frequency instrumentation, fixtures, and devices under test.
| Part Number | VST-L-10M10M-T18KB-XXXX |
|---|---|
| Interface | 1.0 mm Male to 1.0 mm Male |
| Impedance | 50 Ω |
| Frequency Range | DC–110 GHz |
| VSWR | ≤1.45 Max., DC–110 GHz |
| Insertion Loss | See corresponding test report |
| Phase Matching for Pair | ±1 ps |
| Dielectric Withstand Voltage | 400 VRMS |
| Insulation Resistance | ≥5000 MΩ |
| Shielding Effectiveness | ≥90 dB @ 1 GHz |
| Mechanical Durability | ≥500 cycles |
| Cable Type | VXT180KB |
|---|---|
| Construction | Integrated armored RF test cable assembly |
| Assembly Length | Custom (XXXX mm), subject to drawing tolerance |
| Cable Diameter | Ø3.84 ± 0.1 mm |
| Connector Transition | Black heat-shrink tubing |
| Minimum Bend Radius | 30 mm |
| Operating Temperature | -55°C to +125°C |
110 GHz VNA Measurements
High-frequency interconnection between vector network analyzers, extenders, fixtures, and devices under test.
W-Band Component Characterization
Coaxial test paths for connectors, adapters, passive components, modules, and other devices operating into W-band.
Phase-Matched Multi-Path Measurements
Paired cable paths for measurement setups where closely matched electrical delay between channels is required.
RF & Microwave R&D
Laboratory test interconnects requiring 1.0 mm connectivity and broadband operation through 110 GHz.
Insertion loss for the configured assembly length is documented in the corresponding test report. Where phase-matched pairs are required, specify the paired configuration at order stage. For 1.0 mm interfaces, use appropriate precision-connector mating and torque practices. Maintain a bend radius of at least 30 mm and avoid unnecessary mechanical loading at the connector transitions.
Need a 110 GHz cable assembly or phase-matched pair?
Share your required length, interface configuration, phase-matching requirement, routing constraints, and application. Our engineering team can review the assembly configuration before quotation.
Related products
-
DC to 67 GHz 1.85 mm Male to 1.85 mm Male Microwave Test Cable Assembly Using T24KB Low-Loss Ruggedized Flexible Cable
-
DC~26.5GHZ SMA male to SMPM Female .141″ super flexible cable assembly
-
WiFi antenna extension SMA male to SMA male RG174 Cable Assembly
-
SMA female ip68 to SMA male Cable Assembly with 10CM RG316
Need a Quote or Technical Support?
Share the part number, required quantity and application requirements. Our engineering team can assist with product selection, configuration review and quotation support.