SMA Male-to-Male Phase-Stable Low-Loss RF Cable Assembly, DC–26.5 GHz | VST-L-SMSM-W50-XXXX
P/N: VST-L-SMSM-W50-XXXX
- DC–26.5 GHz Phase-Stable Low-Loss Test Cable Assembly
- SMA Male-to-Male | 50 Ω | VSWR ≤1.35
- Stable Phase Performance over Temperature*
- Low Insertion Loss with Assembly-Level RF Test Verification
- High Shielding Effectiveness >90 dB
- Flexible Custom-Length Construction | -55°C to +165°C
VST-L-SMSM-W50-XXXX is a 50 Ω SMA male-to-male phase-stable low-loss RF cable assembly for broadband test and measurement interconnects from DC to 26.5 GHz. The finished assembly is specified for VSWR ≤1.35 through 26.5 GHz and uses the Vinstronics VXW500 / W50 flexible cable platform.
XXXX denotes the assembly length in millimeters. Custom length is supported with defined dimensional tolerances, and insertion loss is documented by RF test report.
DC–26.5 GHz Phase-Stable Low-Loss Test Interconnect
Broadband SMA cable assembly for precision RF and microwave test paths.
SMA Male-to-Male | 50 Ω | VSWR ≤1.35
Finished-assembly interface and return-match specification through 26.5 GHz.
Stable Phase Performance over Temperature
Built on the W50 cable platform, specified for phase stability <750 ppm from -55°C to +85°C.
Low Insertion Loss with RF Test Verification
Finished-assembly insertion loss is referenced to RF test documentation rather than bulk-cable attenuation alone.
High Shielding Effectiveness >90 dB
Shielded construction for controlled RF signal transmission in measurement environments.
Flexible Custom-Length Construction
Ø5.2 mm cable with defined length tolerances and an operating temperature range of -55°C to +165°C.
| Part Number | VST-L-SMSM-W50-XXXX |
|---|---|
| Connector Configuration | SMA Male to SMA Male |
| Impedance | 50 Ω |
| Frequency Range | DC–26.5 GHz |
| VSWR | ≤1.35 Max., DC–26.5 GHz |
| Insertion Loss | See RF test report |
| Dielectric Withstanding Voltage | 1500 VDC |
| Insulation Resistance | ≥5000 MΩ |
| Operating Temperature | -55°C to +165°C |
| Mechanical Durability | ≥500 cycles |
| Cable Diameter | Ø5.2 mm |
| Assembly Length | XXXX mm, custom length |
Phase stability @ -55°C to +85°C
W50 cable attenuation @ 26.5 GHz
Shielding effectiveness
Static / dynamic bend radius
The values above describe the VXW500 / W50 cable platform. The cable uses a silver-plated copper inner conductor, LD PTFE dielectric, silver-plated inner and outer shields, and a gray FEP jacket. Finished-assembly insertion loss depends on assembly length and connector transitions and should be referenced to the corresponding RF test report.
Representative 3 m W50 assembly test: S11, S22, insertion loss, and phase response were measured through 26.5 GHz.
VSWR
Representative sampled values remained below the assembly limit of 1.35 through the measured band.
Insertion Loss
Representative measured insertion loss is approximately 0.75 dB @ 1 GHz, 1.87 dB @ 6 GHz, and around 4.0 dB near 26.5 GHz for the supplied 3 m sample.
Measured values are representative of the supplied 3 m test sample and are not presented as universal limits for every assembly length.
VNA & RF Test Systems
Flexible instrument and DUT interconnection through 26.5 GHz.
Phase-Sensitive Measurements
For RF paths where phase stability and repeatable routing are important.
RF Module & Device Test
Broadband 50 Ω interconnection for component, module, and subsystem evaluation.
Custom-Length Test Routing
Length-configurable assembly for laboratory, production, and system integration.
Series Part Number
VST-L-SMSM-W50-XXXX
XXXX denotes the assembly length in millimeters.
Configuration
SMA Male to SMA Male | VXW500 / W50 cable | 50 Ω | DC–26.5 GHz.
Configure a Phase-Stable Low-Loss SMA Cable Assembly
Specify the required length, routing constraints, and RF test-documentation requirements for quotation or technical review.
Need a Quote or Technical Support?
Share the part number, required quantity and application requirements. Our engineering team can assist with product selection, configuration review and quotation support.